Calculated-industries 4067 User Guide Manual de usuario Pagina 7
- Pagina / 23
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
ConstruCtion Master Plus eZ
7
e
JACK RAFTER C-Ø1
5 FEET 7-5/16 INCH
e
JACK RAFTER C-Ø2
4 FEET 0-1/16 INCH
e
JACK RAFTER C-Ø3
2 FEET 4-7/8 INCH
e
JACK RAFTER C-Ø4
0 FEET 9-5/8 INCH
e
COMMON PLUMB ANGL
33.69°
e
COMMON LEVEL ANGL
56.31°
e
COMMON CHEEK ANGL
45.00°
Find the Jack Rafter Lengths and Angles using a 6′ Run, a 4′ Rise and a 10″
Irregular Pitch:
1. Clear Calculator:
OOO
2. Start Jack Rafter function:
j
3. No Common Pitch:
e
4. Enter 6′ Run:
6fe
5. Enter 4′ Rise:
4fe
6. Enter 10" Irregular Pitch:
10ie
7. Accept default On-Center Spacing (16") and solve for Jack Rafters:
e
COMMON OFFSET LNTH
24-1/16 INCH
e
COMMON RAFTER LNTH
7 FEET 2-9/16 INCH
e
JACK RAFTER C-Ø1
5 FEET 2-1/2 INCH
e
JACK RAFTER C-Ø2
3 FEET 2-7/16 INCH
e
JACK RAFTER C-Ø3
1 FEET 2-7/16 INCH
e
COMMON PLUMB ANGL
33.69°
e
COMMON LEVEL ANGL
56.31°
e
COMMON CHEEK ANGL
51.34°
e
IRREGULAR OFFSET LNTH
16- 11/16 INCH
e
IRREGULAR RAFTER LNTH
6 FEET 3 INCH
e
IR JACK RAFTER I-Ø1
4 FEET 10-5/16 INCH
e
IR JACK RAFTER I-Ø2
3 FEET 5-5/8 INCH
e
IR JACK RAFTER I-Ø3
2 FEET 1 INCH
e
IR JACK RAFTER I-Ø4
0 FEET 8-5/16 INCH
e
IRREGULAR PLUMB ANGL
39.81°
e
IRREGULAR LEVEL ANGL
50.19°
e
IRREGULAR CHEEK ANGL
38.66 °
Jack Rafters – Advanced Function
Required Entries Possible Solutions
Two of the rst three required:
• Pitch
• Run (or Span)
• Rise
On-C enter Spacing*
• Default value: 16"
Common and Irregular
• Jack On-center Spacing*
• Offset Length
• Rafter Length
• Jack Rafter Lengths
• Plumb Angle
• Level Angle
• Cheek Angle
Optional Entries
Irregular Pitch
Horizontal Overhang
Total Fascia Thickness
Common Rafter Thickness**
Hip/Valley Thickness**
Ridge Thickness**
* Default value: 1-1/2"
** On-center Spacing is also a possible solution that displays when both of the following
are true: 1) Common and Irregular Pitches are not equal and 2) Jack Alignment
Preference is set to MATE, rather than ON-CENTER.
** Tail Lengths shown only when Horizontal Overhang is entered.
Find the Jack Rafter Lengths and Angles using an 8" Pitch, a 6′ Run, an 18"
Horizontal Overhang and the default values shown above:
1. Clear Calculator:
Cx
2. Start Advanced Jack Rafter function:
Cj
3. Enter 8" Common Pitch:
8ie
4. Enter 6′ Run:
6fe
5. No Irregular Pitch (Common Pitch used):
e
6. Accept default On-Center Spacing (16"):
e
7. Enter 18" Overhang Run:
18ie
8. No Total Fascia Thickness:
e
(Enter 0 if a value is displayed)
9. Accept 1-1/2" default Rafter Thickness:
e
10. Accept 1-1/2" default Hip/Valley Thickness:
e
11. Accept 1-1/2" default Ridge Thickness and solve for Jack Rafters:
e
COMMON OFFSET LNTH 19-1/4 INCH
19-1/4 INCH
e
COMMON TAIL LNTH
21-5/8 INCH
e
COMMON RAFTER LNTH
8 FEET 11-1/4 INCH
e
JACK RAFTER C-Ø1
7 FEET 4-1/16 INCH
e
JACK RAFTER C-Ø2
5 FEET 8-13/16 INCH
e
JACK RAFTER C-Ø3
4 FEET 1-9/16 INCH
e
JACK RAFTER C-Ø4
2 FEET 6-3/8 INCH
e
JACK RAFTER C-Ø5
0 FEET 11-1/8 INCH
e
COMMON PLUMB ANGL
33.69°
e
COMMON LEVEL ANGL
56.31°
e
COMMON CHEEK ANGL
45.00°
STAIR FUNCTION
Note: Within Preferences, there is a setting for Riser Height that
determines which type of calculation will be used. The default is Target
Riser Height.
• Target Riser Height: Use this setting to get a stair calculation that will get as
close to the stored Riser Height as possible. The calculated Actual Riser Height
will either be shorter or taller than the Target Riser Height.
• Maximum Riser Height: This is used when local building codes prohibit risers
greater than this value. The calculated Actual Riser Height will not exceed the
Maximum Riser Height.
- TABLE OF CONTENTS 1
- GettinG Started 2
- USinG the 3
- ConStrUCtion MaSter PlUS eZ 3
- CONSTRUCTION EXAMPLES 4
- SQUARE-UP AND LxWxH FUNCTIONS 4
- RAFTER FUNCTION 5
- HIP/VALLEY RAFTER FUNCTION 5
- JACK RAFTER FUNCTION 6
- STAIR FUNCTION 7
- CIRCULAR FUNCTION 9
- RAKE WALL FUNCTION 9
- ARC FUNCTION 10
- ARCH STUD FUNCTION 10
- BALUSTER FUNCTION 11
- MATERIALS FUNCTIONS 11
- Optional Entries 12
- DESCRIPTION DEFAULT 14
- Appendix A 17
- Appendix B 18
- BASIC MATH OPERATIONS 19
- SHUT-OFF, BATTERIES, RESET 19
- REPAIR AND RETURN 19
- ConstruCtion Master Plus eZ 21
- Rake Wall function 22
- Spacing function 22
- Open Wall balusters 23
- Cap Wall balusters 23
Relacionado con productos y manuales para Calculadoras, organizadores Calculated-industries 4067 User Guide
Calculadoras, organizadores Calculated-industries 4065 v3.1 Pocket Reference Guide Manual de usuario
(42 paginas)
(42 paginas)
Calculadoras, organizadores Calculated-industries 4065 v3.1 User Guide Manual de usuario
(112 paginas)
(112 paginas)
Calculadoras, organizadores Calculated-industries 4065 v3.1 User Guide Manual de usuario
(110 paginas)
(110 paginas)
Calculadoras, organizadores Calculated-industries 5070-A Pocket Reference Guide Manual de usuario
(45 paginas)
(45 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.070 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales