Calculated-industries 4067 Pocket Reference Guide Manual de usuario

8 C6Tons – Enters or converts a weight or volume value to tons.C1Kilograms (kg) – Enters or converts a weight or volume value to kilograms.Miscellaneo

9 CR0Unit Cost – Stores the Unit Cost for calculating the total cost. To recall this setting, press R0. Default is 0.00 (no Unit Cost).C.Degrees:Minu

10 C÷Reciprocal (1/x) – Finds the Reciprocal of a number (e.g., 8C÷ = 0.125).Construction and Prompting KeysSSquare Up – Calculates the Square-Up (di

11 ChHip/Valley (Advanced) – Calculates advanced lengths and angles for Regular and Irregular Hip/Valley Rafters.jJack Rafter (Basic) – Calculates bas

12 CcRake Wall – Calculates various stud lengths for Rake Walls with or without bases.aArc – Calculates values for Chord Length, Arc Height, Radius, A

13 CNExtras – Accesses functions for Elliptical Arches, Crown Molding, Compound Angles, Polygons and Spacing. Also used to access Preferences for cus

14 Using the Construction Master Plus EZThis Pocket Reference Guide has step-by-step keystroked examples for some of the CMP EZ’s functions. You can s

15 Auto Shut-Off and Auto ShutdownThe LCD display on your calculator is designed to shut off after 4 minutes of non-use. If the display powers off, ju

16 Default ValuesThe table below shows the calculator’s U.S. and Metric Default Values. Default Values can be changed by entering a new value. The new

17 Rake Wall• O.C. Spacing 16"• Top Plate Thickness 1-1/2"Arch Studs• O.C. Spacing 16"• Location 1 = OutsideFunctions — Metric ModeC

The ConstruCtion Master Plus EZ (CMP EZ) is the newest in Calculated Industries′ line of award-winning Construction Master construction-math calculato

18 Materials — U.S. ModeBlocks• Block Height 8"• Block Length 16"• Waste Factor 5%Drywall Sheets• Include Ceiling 1 = Yes• Sheet Lengt

19 Default Values Continued ►Studs• O.C. Spacing 16"• Waste Factor 5%Tile• Grout Width 1/8"• Tile Thickness 1/4"• Waste Factor 5%Tile c

20 Fencing• Number of Rails 2• Maximum Post Spacing 2.4 m• Post Width 69 mmFootings• Footing Area 0.2 sq m• Waste Factor 5%Pavers• Paver Length 215 mm

21 Extras — U.S. Mode Extras — Metric ModeElliptical Arch• O.C. Spacing 16"• Position 1 = OutsideCrown Molding• Corner Angle 90°• Spring Angle 45

22 Construction ExamplesFor each of the functions shown in the Pocket Reference Guide and the User’s Guide there is a box, like the ones shown, with a

23 Continued ►Square-UpRequiRed enTRies soluTionsLengthWidthSquare-UpAreaPerimeterLxWxHRequiRed enTRies soluTions LengthWidthHeightVolumeVertical Su

24 eXaMPle: Enter a 15′ 8" Length, 12′ 6" Width and 4" Height:1. Clear Calculator:OOO2. Start Length x Width x Height function:CS3. Ent

25 eVERTICAL SURFACE AREA 18.777778 SQ FEETeVERTICAL + LxW AREA 214.61111 SQ FEETesquaRe-uP 20 FEET 0-1/2 INCHeLxW AREA 195.83333 SQ FEETePeRiMeTeR

26 Advanced RaftersRequiRed enTRies Possible soluTionsTwo of these required:• Pitch• Run (or Span) • Rise • Common Rafter Length Common Rafter Length

27 * Height Above Plate. If a Top Plate value is shown when you want to enter a HAP, clear the Top Plate value by pressing either O or 0. Then, press

1 The ConstruCtion Master Plus eZ has Basic and Advanced solutions (lengths, angles, quantities, etc.) for these construction calculations:● Rafters●

28 5. Enter 18" Overhang:18ie6. Enter 2-1/4" Total Fascia Thickness:2i1/4e7. Accept 1-1/2" default value for Ridge Thickness:e8. Accept

29 Continued ►eSTANDARD 2/3 HAP 5-13/16 INCHeFULL BEARING HAP 6-3/8 INCHeRise 8 FEET 0 INCHBasic Hip/Valley RaftersRequiRed enTRies Possible soluTion

30 2. Start Basic Hip/Valley function:h3. Enter 8" Common Pitch:8ie4. Enter 12′ Run:12fe5. No entry for Irregular Pitch (Common Pitch used). Solv

31 1. Clear Calculator:OOO2. Start Basic Hip/Valley function:h3. Enter 8" Common Pitch:8ie4. Enter 8′ Run:8fe5. Enter 10" Irregular Pitch an

32 Advanced StairsRequiRed enTRies Possible soluTionsOne of these two required:• Floor-to-Floor Rise• Stair Run Target/Max Riser Height • Default valu

33 Continued ►oPTional enTRies Upper Flooring ThicknessLower Flooring ThicknessNosing LengthRiser Thickness* A warning sign appears on the display w

34 Example using Solve function:Using default values (including 7-1/2" Target Riser Height), solve for Advanced Stairs with a 10' 1" Fl

35 neT flooR-flooR Rise 10 FEET 1 INCHenuMbeR of RiseRs 16.e*ACTUAL RISER HGHT. 7-9/16 INCHenuMbeR of TReads 15.eACTUAL TREAD WDTH 12-5/16 INCHeMIN S

36 Rake Wall FunctionRequiRed enTRies Possible soluTionsTwo of the rst three required:• Pitch• Run• Rise On-center Spacing• Default value: 16" T

37 1. Clear Calculator:OOO2. Start Rake Wall function:Cc3. Enter Pitch:8ie4. Enter Run:6fe5. No Base Height:e6. Accept 16″ default value for On-center

2 Table of ConTenTsKey Denitions ... 3Basic Fu

38 TOP PLATE LENGTH 7 FEET 2-9/16 INCHediffeRenTial lnTH 10-11/16 INCHeINCLINATION ANGL 33.69 °eRAKE WALL STUD Ø1 3 FEET 10-3/16 INCHeRAKE WALL STUD Ø

39 Materials FunctionsPress the N key to access the Materials function. Continued presses of the N key will scroll though the available Materials. Whe

40 StudsRequiRed enTRies Possible soluTionsWall LengthNumber of CornersNumber of WindowsNumber of DoorsOn-center Spacing• Default value: 16″Number of

41 2. Go to Materials function:N (If necessary, continue pressing N until sTuds displays.)3. Start Studs Function:e4. Enter 40' Total Wall Length

42 ExtrasPress C N to access the Extras functions. Continued presses of the N key will scroll through available functions. When you nd the function y

43 Preference SettingsPress C, then N to access the Extras functions. Press N until PRefeRenCes displays and press e. Continued presses of the e key w

44 desCRiPTion defaulToPTionsFractional Resolution 1/16 1/8, 1/4, 1/2, 1/64, 1/32U.S. vs. Metric Mode u.s. Mode MeTRiC ModeArea Answer Format sTandaRd

45 Elliptical Arch FunctionRequiRed enTRies Possible soluTionsHeightWidthStud On-center Spacing• Default value: 16"Stud Location• Default setting

46 eXaMPle: Solve for an Elliptical Arch that is 5' high, 15' wide and has a Base Height of 3'. Studs are Outside the Arch:1. Clear Cal

47 7. Accept 16" default value for Stud O.C. Spacing:e8. Accept default Stud Position (Outside the Arch) and solve for Elliptical Arch:eCenTeR To

3 Key DenitionsBasic Function KeysOOn/Clear Key – Turns on power. When not in a prompting sequence, pressing once clears the last entry and what is d

48 eSTUD PAIR LENGTH Ø4 4 FEET 5-13/16 INCHeSTUD PAIR LENGTH Ø5 5 FEET 8-1/2 INCHeSTUD PAIR LENGTH Ø6 8 FEET 0 INCHBatteryThis model uses one C

49 ResetIf your calculator should ever “lock up,” press Reset – a small hole located above the o key – to perform a total reset. The calculator will r

4840 Hytech DriveCarson City, NV 89706 U.S.A.1-800-854-8075 Fax: 1-775-885-4949E-mail: [email protected] a complete list of key

4 +-x÷=Arithmetic operation keys0 – 9 and .Keys used for entering numbers.CConvert – Used with the dimensional keys to convert between units or with o

5 Dimensional Function KeysyYards – Identies entry as yards, with repeated presses toggling between linear, area and volume units.fFeet – Identies e

6 /Fraction Bar – Used to enter fractions. Fractions can be entered as proper (1/2, 1/8, 1/16) or improper (3/2, 9/8). If the denominator (bottom) is

7 C8Board Feet (Bd Ft) – Enters or converts cubic values to Board Feet. One Board Foot is equal to 144 cubic inches.C2Acre – Enters or converts a squa