Calculated-industries 6250 Manual de usuario

USER’SGUIDEDigital AreaTake-Off ToolModel#6250

USER’S GUIDE — 7FINAL ASSEMBLYThe ultrasonic beams are sent from the right arm of the Puck to the top bar, then refl ected back, and from the left arm

GETTING STARTEDOnce assembly and setup are complete, proceed with the following steps in order to begin measuring.1. When placing the bars and securin

Right-Hand Confi guration ShownUSER’S GUIDE — 9

10 — ULTRA SCALE MASTER®[END] Ends polyline measurement, displaying the total perimeter.[CLOSE —]Completes the polygon and displays the calculated are

USER’S GUIDE — 11[ON/CLEAR]Turns the unit ON and clearsthe display. Holding down the[ON/CLEAR] key for 1.5 seconds also powers the unit off.[CLOSE +]C

[UNDO]Undoes the previous measurement. Allows you to undo the last ten measurements (if applicable) while in measure mode. If a measurement has been c

[M+]Adds the displayed value to accumulative memory (except when setting a Custom Scale).[SET] [M+] (M—)Subtracts the displayed value from the accumu

[MODE]Used to select from the list of available modes (see Built-In Scales section).[SET] [MODE]Used to move back through the list of available modes.

[UNITS]Used to select from the list of available units of measurement (see Units of Measurement section).[SET] [UNITS]Used to move back through the li

The Top Legend displays the following:• SET• M (Memory)The Measure Status and number of sides are displayed here (End or Closed are displayed only whe

INTRODUCTION The Ultra Scale Master has been specifi cally designed to simplify take-offs for all fi elds of construction. Use it for estimating proje

BUILT-IN SCALESThe following modes and scales are available for selection using the [MODE] and [SCALE] keys, depending on whether the puck is set to I

• Only one shape can be measured at a time • A measured Area cannot contain lines that cross each otherSHAPES AND DEFINITIONSThe Ultra Scale Master ca

12MEASURING POLYLINESOPERATING SEQUENCE1. Press the [ON/CLEAR] key twice to clear the display. Place the crosshairs over the fi rst point and press the

MEASURING SIMPLE POLYGONSOPERATING SEQUENCE1. Press the [ON/CLEAR] key twice to clear the display. Place the crosshairs over the fi rst point and press

MEASURING TAKE-OUTSOPERATING SEQUENCE1. Press the [ON/CLEAR] key twice to clear the display. Place the crosshairs over the fi rst point and press the [

AREAADJUSTED AREA5. Press the [CLOSE+] key. The total Area is displayed.6. Press the [M+] key to store the Area in Memory, then repeat steps 1 through

USER’S GUIDE — 23MEASURING COMPLEX POLYGONSOPERATING SEQUENCE1. Press the [ON/CLEAR] key twice to clear the display. Place the crosshairs over the fi r

MEASURING IRREGULAR SHAPESOPERATING SEQUENCE1. Press the [ON/CLEAR] key twice to clear the display. Place the crosshairs over the fi rst point and pres

There are two methods for programming Custom Scales into your Ultra Scale Master. “Measured Custom Scales” allow you to measure a specifi ed Length and

5. The displayed units begin fl ashing, indicating that they are ready to be changed. Press [UNITS] to scroll through the available units.*6. Use [MR]4

SETTING AN ENTERED CUSTOM SCALE (IMPERIAL MODE)1. Press [MODE] until “CUST” is displayed.2. Press [SET] then press [SCALE] [SCALE] to begin entering t

28 — ULTRA SCALE MASTER®LINEAR UNITSFeet-Inch (FEET INCH)*Feet (FEET)Yards (YD)Meters (M)**Centimeters (CM)Millimeters (MM)Inch (INCH)AREA UNITSSquare

USER’S GUIDE — 29APPENDIX A APPENDIX BACCURACY/ERRORS/AUTO SHUT-OFFAccuracy/Display Capacity – The Ultra Scale Masterhas a seven-digit main display,

30 — ULTRA SCALE MASTER®APPENDIX C APPENDIX DSPECIFICATIONS REPAIR AND RETURNWARRANTY, REPAIR AND RETURN INFORMATIONReturn Guidelines1. Please read t

USER’S GUIDE — 31If a defect exists during the warranty period, CI, at its option, will either repair (using new or remanufactured parts) or replace (

Software copyrighted and licensed toCalculated Industries, Inc. byScale Master Technologies, LLC, 2007.User’s Guide copyrighted byCalculated Industrie

TABLE OF CONTENTS SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2PACKAGE CONTENTS . . . . . . .

2 — ULTRA SCALE MASTER®Ultra Scale Master Pro model 6250 (Puck)SETUPPACKAGE CONTENTSYour package contains the following pieces:Female End CapCorner Co

USER’S GUIDE — 3Male End CapShort Refl ector BarLong Refl ector BarCarrying CaseUser’s Guide,Quick Reference Guide,and Quick Setup Sheet

RIGHT-HAND ASSEMBLYAssemble the refl ector bars as shown. Align the corner connector at a 90° angle at the top left corner of the plans.5. Slide Female

4. Insert the Male End Cap into the female end of the Short Refl ector Bar. The Male End Cap is preinstalled for a Right-Hand confi guration.3. Insert t

6 — ULTRA SCALE MASTER®NOTE: Sloping side of the Refl ector Bars face outward.5. Insert the the male end of the second Long Refl ector Bar into the fema